ID.4 2021 ➤
Electrical system - Edition 02.2021
NOTICE
Risk of destroying headlight due to ingress of water.
– When installing the housing cover -1-, make sure that the
seal is correctly seated.
Note
A new housing cover -1- must be used only, if the repair is
carried out for the first time.
– Fit housing cover -1- on headlight.
– Tighten bolts -2-.
– Check headlight settings and adjust headlights if necessary
⇒ Maintenance; Booklet 53.1; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.11
Removing and installing headlight fan
[V407]/[V408]
Special tools and workshop equipment required
♦ ESD workplace -VAS 6613-
♦ Torque screwdriver -V.A.G 1624-
The front left headlight -MX1- and front right headlight -MX2-
will henceforth be referred to as “headlight”.
The left headlight fan -V407- and right headlight fan -V408- will
henceforth be referred to as “headlight fan”.
Removal and installation are described for the left vehicle side
as an example.
Removing
– Remove headlight ⇒ Rep. gr. 94; Removing and installing
headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out
at an ESD workplace.
– Place headlight onto ESD workplace -VAS 6613-.
74
Rep. gr.94 - Lights, bulbs, switches - exterior
ID.4 2021 ➤
Electrical system - Edition 02.2021
– Use a hammer to carefully release housing cover -1- along
predetermined break line -2-.
– Remove housing cover -1- from headlight.
– Unscrew bolts -2-.
– Disconnect electrical connector -3-.
– Remove fan -1-.
Installing
Install in reverse order of removal, observing the following:
NOTICE
Risk of destroying headlight due to ingress of water.
– When installing the housing cover -1-, make sure that the
seal is correctly seated.
Note
A new housing cover -1- must be used only, if the repair is
carried out for the first time.
2. Headlights
75
ID.4 2021 ➤
Electrical system - Edition 02.2021
– Fit housing cover -1- on headlight.
– Tighten bolts -2-.
– Check headlight settings and adjust headlights if necessary
⇒ Maintenance; Booklet 53.1; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.12
Removing and installing output mod‐
ule 1 for LED headlight [A27]/[A31]
2.12.1
Removing and installing output mod‐
ule 1 for LED headlight [A27]/[A31],
ECO headlights
Special tools and workshop equipment required
♦ ESD workplace -VAS 6613-
♦ Torque screwdriver -V.A.G 1624-
The front left headlight -MX1- and front right headlight -MX2-
will henceforth be referred to as “headlight”.
The output module 1 for left LED headlight -A31- and output
module 1 for right LED headlight -A27- will henceforth be refer‐
red to as “output module”.
If the output module is renewed, perform the test plan for the
renewal of the output module using ⇒ Vehicle diagnostic tester.
Removal and installation are described for the left vehicle side
as an example.
Removing
– Remove headlight ⇒ Rep. gr. 94; Removing and installing
headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out
at an ESD workplace.
– Place headlight onto ESD workplace -VAS 6613-.
76
Rep. gr.94 - Lights, bulbs, switches - exterior
2024 VW ID.4 Owner's Manual
